Drago

Occasional handbrake fault

Recommended Posts

Hi,

Just sold my beloved X type and got a 3.0 Sport S type. Nice motor, reliable but has a glitch with the electric handbrake. Sometimes when you turn the ignition a fault shows up saying the handbrake is locked. It won't move. Turning the engine off and restarting after all the lights go out will sort the problem. I have found that manually taking the brake off with the ignition on works okay but on occasion you get a fault saying that you cannot apply the hand brake with an amber warning light. Again, turn the engine off and it resets. Other than that, car works fine. Can anyone tell me if this is due to a sensor or some easy fix? Also, have fitted an Adamesh exhaust and have fallen in love with the new growl I'm getting, but a bit disappointed that it's not as throaty as the X type. Anyone else think this? Would changing the induction set up help?

Thanks

Share this post


Link to post
Share on other sites

Hi Andy,

Disconnect the battery for 10 seconds then reconnect.

You will have to keep your ignition key in your pocket, as the alarm will go off when you reconnect.

When you start the engine,  just follow the message instruction --  press both footbrake and hand brake. You will need to have your radio code to hand.

You will also have to reset all windows, volume, clock etc.

Also, to stop it happening too often keep you battery charged.

Regards,

Peter.

 

Share this post


Link to post
Share on other sites

Hi Peter,

Many thanks for the info. Is this a common fault? doesn't seem to effect the car driving, just irritating at times having an error message and little yellow flashing light.

Thanks again

 

Andy

Share this post


Link to post
Share on other sites

Hi Andy, 

It is something that happens when the battery is low.  I charge my car once a fortnight as I don't do a big mileage.

Regards,

Peter. 

Share this post


Link to post
Share on other sites

Hi Peter,

Many thanks. Seem's to happen more when the temp drops so reckon I'll treat myself to a new battery.

Thanks again,

Regards,

Andy

Share this post


Link to post
Share on other sites

Hi Andy, 

Batteries only seem to last for 5 years on Jaguars  --  so much electrical whatnots!

Regards,

Peter. 

Share this post


Link to post
Share on other sites
On 10/3/2019 at 11:40 AM, Drago said:

Hi,

Just sold my beloved X type and got a 3.0 Sport S type. Nice motor, reliable but has a glitch with the electric handbrake. Sometimes when you turn the ignition a fault shows up saying the handbrake is locked. It won't move. Turning the engine off and restarting after all the lights go out will sort the problem. I have found that manually taking the brake off with the ignition on works okay but on occasion you get a fault saying that you cannot apply the hand brake with an amber warning light. Again, turn the engine off and it resets. Other than that, car works fine. Can anyone tell me if this is due to a sensor or some easy fix? Also, have fitted an Adamesh exhaust and have fallen in love with the new growl I'm getting, but a bit disappointed that it's not as throaty as the X type. Anyone else think this? Would changing the induction set up help?

Thanks

I've just had the same problem with my 2.7 after fitting a new brake booster.  The handbrake and brake fault light was on and the gear shift was stuck in park, on re inspecting under the dash I noticed that the brake peddle has a flat plate on it which activates the two switches, the bottom switch activates the cruise control and the top one activates the gear shift gate, the handbrake,  the brake fault light and the brake lights on inspection I noted that the activation plate on the peddle was just and so touching both switches, I tried adjusting the peddle on the brake booster rod but It if you do that the rod keeps falling out from its mount on the peddle, very dangerous,  my solution was to start the engine and depress the puddle as far as possible with your elbow and fit a piece  of windscreen washer tube, about 1/2 an inch long over the plastic rod on the switch so as to extend it by only about 1/4" l did this on both switches and since then have had no troubles at all everything including the cruise control now work.j

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...