dekor8tor

On 10/21/2016 at 8:29 PM, dekor8tor said:

Hi all 

just need a bit of help with my s type 2.7d 2006 i havent been able to use the car for three weeks because of the problems

i came back to the car on the car park went to start it which it did and i must have got every error msg going

cannot apply parking brake, abs fault, traction control fault, restricted performance,and auto stuck in park which the aa man managed to get it out of park

i was told that it was the battery which is less than 1 yr old and is the recommended varta silver so i took the battery back from where i bought it and it checked out fine since i have put the battery back on i have another problem the engine will not crank i put my delphi diagnostic on and read the codes and i got 2 which were p1934 and the other one was u0121

lost comms with abs module when i try to communicate with the abs module it wont let me also i cannot put the epb into service mode

just wondering if anyone has any thoughts or help on this which would be appreciated

 

hi everyone had a weekend looking at the jag and i have written down everything that i have found

Error Messages on the dash as follows

ABS Fault

Traction Control Fault

Restricted Performance

Cannot apply park brake

Apply foot and park brake

Brake Fluid low

i then connected my foxwell auto pro scanner and got the following dtcs

parking brake control module  U0121  permament  lost communication with ABS control module

PowerTrain control module U0121 temporary lost comm with abs module, P1934 Temporary vehicle speed signal, U0164 Temporary lost communication with heating ventilation a/c control module

Climate control module U2521 missing msg from ABS module

Instrument pack U1900 CAN communications bus fault, U2521 Missing message from the ABS

Transmission control module P1799 CAN transmission control module/ABS control module circuit malfunction

Drivers door module U1o41 SCP vehicle speed signal invalid or missing data

General electonics control module U1041 vehicle speed not obtained

Rear electonic module U1041 SCP vehicle speed signal invalid or missing data

 

i think i have got a few problems but i hope it is a simple fix the car was running fine i went to the supermarket came out and got the above problems

any help and advice is greatly appreciated

 

Update 3rd November

hi all thought i would do an update of what i did to cure the above problem the abs module connector plug upon checking had lost the battery live to pin num 2 on the plug

so off came the front bumper and headlight removed i stripped the tape from the harness and found the broken wire i rejoined and soldered the wire cleared the dtcs the car is now running perfect

hi joe and peter thanks for your help the starter motor isnt makjng a noise it isnt even clicking the starter motor relay is clicking all this started to happen when i took the battery off to have it checked because of all the error msgs that were coming up

Hi joe thanks for that i understand what you are saying where i bought the battery from who is a battery specialist charged the battery overnight for me

The problem is that i cannot get the engine to turn over ignotion comes on but when i turn the key nothing happens the starter motor relay is working i can feel it clicking 

Hi all 

just need a bit of help with my s type 2.7d 2006 i havent been able to use the car for three weeks because of the problems

i came back to the car on the car park went to start it which it did and i must have got every error msg going

cannot apply parking brake, abs fault, traction control fault, restricted performance,and auto stuck in park which the aa man managed to get it out of park

i was told that it was the battery which is less than 1 yr old and is the recommended varta silver so i took the battery back from where i bought it and it checked out fine since i have put the battery back on i have another problem the engine will not crank i put my delphi diagnostic on and read the codes and i got 2 which were p1934 and the other one was u0121

lost comms with abs module when i try to communicate with the abs module it wont let me also i cannot put the epb into service mode

just wondering if anyone has any thoughts or help on this which would be appreciated

hi everyone had a weekend looking at the jag and i have written down everything that i have found

Error Messages on the dash as follows

ABS Fault

Traction Control Fault

Restricted Performance

Cannot apply park brake

Apply foot and park brake

Brake Fluid low

i then connected my foxwell auto pro scanner and got the following dtcs

parking brake control module  U0121  permament  lost communication with ABS control module

PowerTrain control module U0121 temporary lost comm with abs module, P1934 Temporary vehicle speed signal, U0164 Temporary lost communication with heating ventilation a/c control module

Climate control module U2521 missing msg from ABS module

Instrument pack U1900 CAN communications bus fault, U2521 Missing message from the ABS

Transmission control module P1799 CAN transmission control module/ABS control module circuit malfunction

Drivers door module U1o41 SCP vehicle speed signal invalid or missing data

General electonics control module U1041 vehicle speed not obtained

Rear electonic module U1041 SCP vehicle speed signal invalid or missing data

i think i have got a few problems but i hope it is a simple fix the car was running fine i went to the supermarket came out and got the above problems

any help and advice is greatly appreciated